Bottle Fillers & Disconnects
Duotight 9.5 mm (3/8 in.) x 1/4 in. Flare
This Duotight fitting with 1/4" Flare is perfect for flared gas and beverage ball lock and pin lock disconnects. This Duotight fitting is compatible with EVABarrier 9.5 mm OD Tubing. Although this fitting would also fit a beverage disconnect, 9.5 mm OD EVABarrier is only recommended for beverage line in long draw draft set ups. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Note: Ball lock fitting and regulator not included.
$3.49
Tapcooler Counter Pressure Bottle Filler
The Tapcooler Counter Pressure Bottle Filler is the #1 way to fill bottles of your homebrew, directly from your kegging system. No more messing with alternate liquid lines or hard to assemble contraptions. Just fit the Tapcooler into any forward sealing faucet (i.e. Perlick, Intertap/Ultratap/Vent-Matic, etc..), hook up a CO2 line, and you're good to go. Fill bottles for a competition, or just fill a couple take home bottles for your friends. The Tapcooler is quick and easy to use, and will help maintain the flavor, aroma, and carbonation level of your beer so it tastes the same out of the bottle as it would out of the tap. For starters, a counter pressure bottle filler is better than most bottling solutions, as the bottle is under pressure while the carbonated beer flows in. Because the interior of the bottle is pressurized there is minimal loss of the CO2 in solution. The Tapcooler solution improves upon the standard counter pressure filler, as it plugs directly into your draft system faucet (tap). Most solutions require you to hook up a separate liquid line, which is not something standard draft systems have setup and requires additional prep (i.e. more time). With the Tapcooler, you can have it setup and ready to go in less than a minute! The Tapcooler design is also advantageous because after you are done filling the bottle, it stays in place hooked up to your faucet vs. other fillers require you to set aside and pick back up again for the next bottle. Connecting your CO2 line is also a snap. You can either hook up directly with a 3/16 in. push-fit line, or connect your line to the included barb fitting. Optionally, you can purchase the gas ball lock adapter, which gives you the ability to attach a gas (gray) disconnect directly to the filler unit. This optional accessory is a must have in our book! With the Tapcooler design, your beer and CO2 are filled from the bottom of the bottle through the telescoping bottle connection tube. First CO2 flows down into the bottom of the bottle to flush from the bottom up. Next you open the tap and beer flows down the same tube, filling from the bottom up. The result is a more effective purging of oxygen and little to no foam during the filling process The telescoping bottle connection tube allows you to fill bottles as small as 4.5 in. tall up to 12.5 in. You can fill taller bottles with the Tapcooler, but the tube will not reach the bottom of the bottle, which can lead to some splashing. When filling large mouth containers, a bottle stopper of suitable size and with a 9 mm hole may be used. The filler features a push button CO2 purge valve, which allows you to purge the bottle of oxygen before & after filling. It also includes an adjustable pressure relief valve, giving you the ability to change the filling speed. The pressure relief valve also acts as an overflow port for excess beer/foam to escape when filling. One of our most favorite features of the Tapcooler, is that is super easy to clean. Cleaning other bottle fillers can be a chore and take lots of time. The Tapcooler comes apart easily and allows you to clean all parts effectively and easily after each use. All metal parts that come into contact with your beer, are made of stainless steel (SS304). The barb and ball lock CO2 adapters are made of aluminum. Lastly, the Tapcooler comes chock full of optional accessories, which will adapt your filler perfectly to your setup. See the related parts section below for list of them! Forward-Sealing Faucet CompatibilityTapcooler fits Intertap, Nukatap, Ultratap, Vent-Matic, and Perlick 600 series faucets. These fillers can be converted to fit Perlick 500 series with the optional tap connector. Cannot be used with ventilated beer taps, i.e. non-forward sealing beer taps. Hooks up directly to any forward sealing faucet for quick and easy use. Quick setup and easy maintenance. Perfect for bottling for competitions, sending bottles home with friends, or just to have some bottles on the go! A range of accessories are offered for more range and easier use! Purge bottles with CO2 before and after filling for longer lasting beer! Pressure relief valve allows for control over filling speed and allows excess foam to escape for the perfect pour every time! Stainless Steel design Easy to use and clean!
$79.99
Counter Pressure Bottle Filler
Flush and fill your bottles with ease. The valve has three positions: off, beer, and gas. Insert filler into the bottle in the off position, switch to gas to flush the bottle with CO2, and then switch to beer to fill your bottle. You can control the speed of your flow with the adjustable pressure relief. This filler is designed for use with 12 oz. bottles but can be used with larger formats by attaching a small piece of 1/4" tubing to the filler.
$70.00
5/16'' Barbed Co2 Line Tee, Stainless Steel
Stainless steel barbed tee commonly used to splice/split Co2 draft hose. Specifications 304 Stainless Steel 5/16" ID Barbs T Fitting Splices Together 5/16" I.D. Vinyl to 5/16" I.D. Vinyl 5/16" I.D. Vinyl to 3/8" I.D. Poly 3/8" I.D. Poly to 3/8" I.D. Poly
$8.99
Duotight Push-In Fitting - 8 mm (5/16 in.) x 3/8 in. BSP
This Duotight fitting with 3/8" male thread can be used to convert any female threaded 3/8" connection to Duotight. Comes with seated O-ring. Compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18067
$2.99
5/16" x 1/2” Splicer - Stainless Steel
Beer line 5/16" x 1/2" stainless steel barbed splicer. Splices 1/4" I.D. Vinyl to 3/8" I.D. Vinyl 1/4" I.D. Vinyl to 1/2" I.D. Poly 5/16" I.D. Poly to 1/2" I.D. Poly Specifications Type: Straight Connectors Material: 304 Stainless Steel
$3.49
1/2” x 1/2” Vinyl Tubing Splicer - Stainless Steel
Vinyl beer line 1/2" x 1/2" stainless steel barbed splicer. Splices 1/2" I.D. Vinyl to 1/2" I.D. Vinyl Specifications Type: Straight Connectors Material: 304 Stainless Steel O.D.: 7/16" I.D.: 1/2"
$3.99
Duotight 8mm (5/16) x 1/4" BSP Male Bulkhead
This Duotight Bulkhead is the same one used for installing the Thermowell into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 8 mm OD Tubing or 5/16" OD stainless or copper tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
$4.49
6.5 mm (1/4 in.) x 9.5 mm (3/8 in.) Reducer
Duotight 6.5 mm (1/4 in.) x 9.5 mm (3/8 in.) Reducer Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$3.99
Tapcooler Ball Lock Adapter
Easily connect a gas ball lock fitting into your Tapcooler Counter Pressure Bottle Filler with this handy ball lock CO2 adapter! Made of aluminium.
$14.99
Push In Pressure Gauge
This 0-40 psi, push-in pressure gauge comes with an 8 mm (5/16 in.) barb and is specifically designed to be compatible with 8 mm Duotight fittings. It's the ideal companion to the BlowTie Diaphragm Spunding Valve, allowing you to dial in your blow off setting for pressure fermentations or pressure transfers. Triple-scaled to read in psi, bar, and kPa.
$8.99
Grommet for 3/8'' ID SS Tubing
Rubber grommet for chrome plated brass ferrule with 3/8" ID bore.
$0.95
Duotight Push-In Fitting - 8 mm (5/16 in.) Plug
This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C)
$1.49
Chrome Plated Brass Ferrule for 3/8'' ID SS Tubing
Brass ferrule for jockey box cooling coil. Chrome plated brass with a 3/8" ID bore.
$3.50
3/8'' x 50' Stainless Draft Coil
3/8" x 50' 304 Stainless Steel Coil This 3/8" draft coil will hold more beer than your typical 5/16" coil meaning it will cool your beer quicker and it will take less CO2 to serve your beer. Using less CO2 will help reduce over carbonating your beer which results in less foam.
$95.00
Duotight 9.5 mm (3/8 in.) x 1/2 in.FPT
This Duotight to 1/2" female thread fitting can be used to connect beverage or gas line to any fitting with 1/2" MPT. Compatible with EVABarrier 9.5 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$2.99
$1.25
3/16” x 3/16” Splicer, 304 S/S
Stainless steel barbed splicer generally used for attaching two pieces of beer draft line. Specifications 304 Stainless Steel OD: 1/4" ID: 1/16" Splices Tubing Sizes 3/16" I.D. Vinyl to 3/16" I.D. Vinyl 3/16" I.D. Vinyl to 1/4" I.D. Poly 1/4" I.D. Poly to 1/4" I.D. Poly
$3.49
1/4" x 1/2” Splicer - Stainless Steel
Beer line 1/4" x 1/2" stainless steel barbed splicer. Splices 3/16" I.D. Vinyl to 3/8" I.D. Vinyl 3/16" I.D. Vinyl to 1/2" I.D. Vinyl 1/4" I.D. Poly to 1/2" I.D. Vinyl Specifications Type: Straight Connectors Material: 304 Stainless Steel
$3.99
45 degree 1/4" Swivel Elbow
45 degree barbed swivel elbow stem and nut. Specifications: Barb with fit 1/4" ID tubing. Nut is a 1/4" flare fitting. 304 Stainless Steel.
$4.49
Tapcooler Pressure Relief Valve Drain Tube
This drain tube attaches to the pressure relief valve on the Tapcooler Counter Pressure Bottle Filler to drain away excess beer! Having issues with foam and beer leaking from the Tapcooler Counter Pressure Bottle Filler? This pressure relief drain tube hooks directly up to the pressure relief valve of the Tapcooler to drain away excess beer and foam! Measuring 1 meter long (roughly 40 inches), the end of the tube can be placed in a growler or other receptacle so you can keep filling bottles without spillage!
$8.99
Tubing Quick Disconnect, 1/4'' barb x Male
Male quick disconnect with a 1/4" female barb. Includes a shutoff that seals the valve when not connected to tubing.
$9.99
SS304 Cooling Coil - 50' x 5/16'' OD
304 Stainless Steel Cooling Coil. Includes grommets, ferrules, and hex nut fittings for easy connection to shanks. Specifications: Material: Stainless Steel 304 Size: 50ft x 5/16" OD (Tube) Diameter: 5.25" (coil) Height: 6.75" (coil)
$99.99
Duotight Push-In Fitting - 9.5 mm (3/8 in.) Plug
This Duotight plug is used to block up your 9.5 mm (3/8") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C)
$1.59
Duotight - 9.5 mm (3/8 in.) Joiner
This Duotight joiner fitting is compatible with EVABarrier 9.5 mm OD tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$2.99
Deluxe Counter Pressure Bottle Filler
Flush and fill your bottles with ease. This filler has all the great features of the Counter Pressure Bottle Filler with the added benefit of a pressure gauge and flared connections. The gauge helps monitor pressure inside of your bottles and the flared connections make cleaning your lines a breeze. The valve has three positions: off, beer, and gas. Insert filler into the bottle in the off position, switch to gas to flush the bottle with CO2, and then switch to beer to fill your bottle. You can control the speed of your flow with the adjustable pressure relief. This filler is designed for use with 12 oz. bottles but can be used with larger formats by attaching a small piece of 1/4" tubing to the filler.
$90.00
Counter Pressure Accessory Package
Use this kit with your counter pressure bottle filler. This kit includes a gas line tee, gas and beverage quick disconnects, 6' of gas line, flare fittings, and 5' of beer line.
$40.00
Adjustable Pressure Relief Valve with Ball Lock Coupler
This adjustable pressure relief valve can be used when transferring or filtering beer from one keg to another. The end of the pressure valve turns to let you adjust the amount of pressure released.
$24.99 $21.99
$1.00
Duotight 9.5 mm (3/8 in.) x 1/2 in. BSP
This Duotight fitting with 1/2" male thread is perfect for attaching to the Copper Counterflow Chiller and using with 1/2" female threaded Camlock and QD fittings. Compatible with EVABarrier 9.5 mm OD tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$2.99
3/16” x 1/4” Splicer, Stainless
3/16" x 1/4" hose splicer, 303 stainless (for 3/16"ID and 1/4"ID hose).
$2.99
Gas Pressure Relief, Stainless
Gas Manifold - Pressure Relief Valve 1/4" Male ThreadingSet to blow off at 55psi.
$10.00
1/2” x 1/2” Splicer - Stainless Steel
Beer line 1/2" x 1/2" stainless steel barbed splicer. Splices 3/8" I.D. Vinyl to 3/8" I.D. Vinyl 3/8" I.D. Vinyl to 1/2" I.D. Poly 1/2" I.D. Poly to 1/2" I.D. Poly Specifications Type: Straight Connectors Material: 304 Stainless Steel O.D.: 1/2" I.D.: 3/8"
$3.49
1/4" Barbed Ball Valve
Plastic ball valve with 1/4" barb fittings on each end.
$9.99 $6.99
Push-in 9.5 mm (3/8 in.) Check Valve
Compatible with EVABarrier 9.5 mm OD tubing. It has a low opening pressure of 1 psi, and since it cannot be opened or taken apart, it is recommended for gas applications only. The internal components are made from stainless steel. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Made from food-grade acetal plastic Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$7.99 $4.99
Duotight Push-In Fitting - 9.5mm (3/8 in.) Female Bulkhead
This Duotight fitting is designed to go through the wall of a tank, housing, or wall, similar to a pass through shank, so you can run EVABarrier tubing from one side to the other. Compatible with EVABarrier 9.5 mm OD tubing. With the lock nuts in place, there is approximately 1" of pass through threading. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
$3.49
