Keg Couplers

This Ball Lock Disconnect (Liquid) by CM Becker provides a secure liquid flow with a durable plastic coupler and 1/4" MFL male flare thread. Its reliable seal and robust construction make it an ideal choice for Cornelius kegs.

Read more less

CM Becker plastic ball lock gas in coupler with 1/4" MFL.  Quick disconnect for ball lock Cornelius (Corny)-type kegs.The 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available.

Read more less

The "D" system keg coupler, also known as American Sankey, is the most common system available in the USA. It is used by all the major North American breweries as well as most craft breweries. The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank/regulator and the beer hose to the beer faucet attach to the coupler. Features Chrome plated brass body Tin-nickel plated probe Short handle is ideal for the smaller diameter 1/6 kegs Specifications System: "D" (American Sankey) Body Material: Chrome plated brass Probe Material: Tin-nickel alloy plated Handle Style: Lever Gas Port: 3/8" O.D. Barb (To fit 5/16" I.D. Gas Hose) Beer Port: 7/8"-14 Thread (U.S. Beer Industry Standard) Height: 3-13/16" Manufacturer: Micro Matic ⚠️WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. www.P65Warnings.ca.gov

Read more less

Liquid coupler for cornelius keg with 1/4 barb.

Read more less

This Ball Lock Disconnect (Gas) connector is the perfect solution for cornelius kegs. Made by CM Becker plastic, this 3/8'' barbed connector is designed for a long-lasting and reliable connection.

Read more less

Adapt your sanke style coupler to accept a ball lock coupler with this stainless steel fitting.   Liquid ball lock post for sanke coupler.   Stainless Steel

Read more less

Adapt your sanke style coupler to accept a ball lock coupler with this stainless steel fitting.   Gas ball lock post for sanke coupler. Stainless Steel.

Read more less

Micro Matic 304 stainless steel, Sankey D probe coupler for American kegs.  Good for dispensing beer, wine, and cider. "D" system is the most common system available in the U.S., also known as American Sankey. It is used by all the major breweries Anheuser-Busch, Miller, Molson-Coors, and Labatt as well as most craft breweries. The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank/regulator and the beer hose to the beer faucet attach to the coupler. Specifications: 304 stainless steel body improves durability and resistance to chemicals 304 stainless Steel probe for the ultimate in purity Excellent for beer, wine, and cider 304 stainless steel handle fork for added strength Short handle is ideal for the smaller diameter 1/6 kegs NSF approved Made in the USA

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 8 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 8 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing.  6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.

Read more less

This pump is a budget solution for dispensing beer and cider at parties, picnics, and special occasions.  Since this is a hand pump tap, it is best when dispensing a whole keg that same day or night. For use with American sanke D style kegs.

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 8 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Beverage Out Direct connect 8 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning

Read more less

This stainless steel flow control disconnect will eliminate the guess work of balancing draft lines. Use the adjustment knob to dial in the ideal flow resistance based on the beverage being served. Flow control disconnects perform better than flow control faucets as they put the point of resistance at the beginning of the beverage line instead of at the end. When beer passes through the flow control apparatus inside the faucet, turbulence will cause carbonation to come out of solution and foaming issues occur.  Flow control disconnects on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. 1/4" flare thread for beverage line connection. Please note: make sure your keg post o-rings are in good condition before using this fitting. If they are overly worn and you are not getting a good seal, replace the post o-ring then re-attach the ball lock fitting.

Read more less

This pump is great for parties and special occasions. This is a hand pump tap, so your beer will go flat overnight. This is designed for parties where you plan on drinking the whole keg that same day or night.  American Sanke D System Black Lever Coupler Low Profile Plastic Pump

Read more less

D system keg pump has a chrome body and is perfect for home and party draft beer dispensing. "D" system is the most common system available in the US, also known as American Sankey. Features: Short stroke pump for quick pumping! Lever handle for easy keg tapping Forged brass body for durability Short handle is ideal for the smaller diameter 1/6 kegs. View Cleaning Features  

Read more less

Make your cleaning day a breeze with this QD Jumper post.  No need to remove the Ball lock disconnects at all. The cleaner solution goes right through the Ball Lock Keg cleaning post. Connect multiple beer lines and Ball lock kegs in a daisy chain and clean them all in one go. Specifications: Made of Stainless steel material. Includes O rings on both ends. Jumper between the beer lines for easy cleaning. Ball lock kegs are widely used in home-brewing. Hence a handy tool for all home-brewers. Note: Pictured ball lock coupler not included.

Read more less

304 Stainless steel ball lock liquid (beverage out) side connector with 1/4" flare connection.

Read more less

This CM Becker pin lock style disconnect is made in Germany and assembled in the USA.  It is for the three pin liquid connection and features a short body and a 1/4" flare connection. Most commonly, you will need a 1/4" swivel nut with 1/4" barb to connect the standard 5/16" red gas line. For EvaBarrier tubing, a Duotight 8mm with 1/4 flare fitting is a common connector.

Read more less

If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects.  The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Features: Ball Lock Quick Disconnect - Bev Out Adjustable flow rate Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning

Read more less

304 Stainless steel ball lock gas (in) side connector with 1/4" flare connection.

Read more less

This CM Becker pin lock style disconnect is made in Germany and assembled in the USA.  It is for the two pin gas connection and features a short body and a 1/4" flare connection. Most commonly, you will need a 1/4" swivel nut with 5/16" barb to connect the standard 5/16" red gas line. For EvaBarrier tubing, a Duotight 8mm with 1/4 flare fitting is a common connector.

Read more less

This inline check valve can be used with any gas-in ball lock or pin lock flared disconnect. It allows gas to flow through while preventing the backflow of liquid. Made in Germany and assembled in the USA by CM Becker.

Read more less

Plastic ball lock gas in coupler with 1/4" MFL.  Quick disconnect for ball lock Cornelius (Corny)-type kegs. This disconnect has an internal check valve that will allow the gas to flow out, but won’t allow backflow of liquid back into your system.

Read more less

304 Stainless steel ball lock liquid (beverage out) side connector with 1/4" barb connection.

Read more less

Plastic ball lock gas in coupler with 1/4" MFL.  Quick disconnect for ball lock Cornelius (Corny)-type kegs. This disconnect has an internal check valve that will allow the gas to flow out, but won’t allow backflow of liquid back into your system. Internal Check Valve protects your system from liquid back flow! Made in Germany and assembled in the USA by CMB. Extremely high quality for years of service. NSF Approved for Food Grade Service!

Read more less

Convert a commercial sanke keg to be used with ball lock fittings. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. **Be sure to always depressurize the keg before removing the tapping head.** Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi)

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 9.5 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Beverage Out Direct connect 8 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning

Read more less

This A System "German Slider" keg coupler is manufactured my Micro Matic, a leader in the beverage dispensing industry.  The A system tap is commonly referred to as the "German Slider" because it slides onto the valve face.  This makes for a quick and easy installation.   The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank/regulator and the beer hose to the beer faucet attach to the coupler. It is used by breweries such as Hoegaarden, Paulaner, Spaten, and Warsteiner. FEATURES Slide on keg connection 304-grade stainless steel probe for the ultimate in purity Short handle ideal for 1/6th barrel kegs and keg with a rubber chime Ergo lever handle Easy to engage: push down to tap/pull up to untap PRV (pressure relief valve) Fits A System keg valves Easy to use Excellent for beer, cocktails For home or commercial use

Read more less

When you got vertical space challenges, a low profile keg coupler is the only solution. Low Profile D System Keg Coupler comes with PRV (55 Psi Pressure Release valve) and is  NSF Certified. Release excess pressure from a keg pulling PRV ring. Co2 Gas-IN barb of keg coupler is suitable for red beer gas hose (5/16" ID). The body and all internal parts of the dispense coupler are made from 304 stainless steel grades. This is a corrosion-resistant grade and is also considered the best in the food industry. Krome dispense is a leading manufacturer of keg beer dispense keg couplers. Suitable for domestic kegs All stainless 304 body and contact with the beer Silicon check valve included CO2 side of the keg coupler Gas inlet and Beer outlet on sides of the keg coupler Standard industry Parts – like beer nut and gas tailpieces included Once installed, requires less than 3.75″ of vertical space to operate. Saves space in keg stacking setup How to tap low profile keg coupler? Tapping a low profile keg Sankey coupler is easy. Simply twist the coupler on a domestic beer keg. D system keg couplers are also called American Sankeys as they work with most North American kegs. USA and Canadian brands, like Budweiser, Busch, Coors Light, Killian’s, Labatt, Michelob, Miller Lite, Milwaukee’s Best, Molson, Moosehead, OV, Pete’s Wicked, Sam Adams use D type keg valves.

Read more less

D system Keg coupler Chrome-plated Body & Probe US Sankey keg coupler to dispense draft beer from the keg. Tap the keg with ease with this lever handle style coupler. Place the coupler base aligned over the valve. Pull the handle out and put down to lock the coupler in this position. You can now enjoy an uninterrupted flow of your favorite beer. D system keg couplers are also called American Sankeys as they work with most North American kegs. USA and Canadian brands, like Budweiser, Busch, Coors Light, Killian’s, Labatt, Michelob, Miller Lite, Milwaukee’s Best, Molson, Moosehead, OV, Pete’s Wicked, Sam Adams use D type keg valves. Both body and probe made of Brass with Chrome plating. Durable and less expensive than SS counterpart. D system keg coupler is the predominant valve system used by most domestic and commercial breweries in the USA. This is a domestic keg tapping device for US local beers that draws beer out from kegs. Use a reliable and durable keg coupler. Choose from the various options and material combinations that suit your needs best. Both coupler body and probe made of Brass material with a layer of Chrome. Durable and built for heavy-duty use in commercial places like pubs and bars.  Pressure Relief valve included for safety.  Releases overpressure gas at 56 – 65 PSI All Krome keg couplers are NSF approved.

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 6.35 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 6.3 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing.  6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.

Read more less

Keg coupler (tavern head) for S-system (Euro-Sanke, Heineken) kegs. Includes integrated washer/check valve and nut on the gas in side. Nut, nipple, and washer assembly included for both gas and beer inlet/outlet.  Nickel coated body with stainless steel probe. This item does not come with a pressure relief valve.  

Read more less

304 Stainless steel ball lock gas (in) connector with 1/4" barb connection.

Read more less

This silicone elbow is a replacement for the elbow provided in the PCO38 Tapping Head Kit.  Allowing for a 90° connection between the barb on the yellow liquid plastic carbonation cap and the 6.3 mm OD dip tube provided in the kit. KegLand Part Number: KL26260

Read more less

Convert draft shanks or keg couplers for use with 1/2" female threaded fittings. Featuring a hex nut exterior for easy wrench adjustments. The female side is standard beer thread which is used on both ports of standard keg couplers and the tail end of draft shanks. Once installed, you can adapt these input/output ports to any 1/2" fittings and valves you might find useful. The 1/2" male BSP end may require teflon tape if used with 1/2" NPT fittings. Comes in a pack of 2

Read more less

Micro Matic has developed a new dispense head for KeyKeg™ one-way kegs which makes it even safer, easier and more convenient to use. The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank / regulator and the beer hose to the beer faucet attach to the coupler. Features: Convenient to use integrated degassing function Degassing takes only 10 seconds No special tools needed for degassing 304 Stainless Steel probe for the ultimate in purity Excellent for beer, wine, coffee, cider, etc. Easy to tap with no product splash Easy to engage handle: push down to tap/pull up to untap Specifications: System: KeyKeg™ Probe Material: 304 Stainless Steel Handle Style: Ergonomic Lever Gas Port: 3/8" O.D. Barb (To fit 5/16" I.D. Gas Hose) Beer Port: 7/8"-14 Thread (U.S. Beer Industry Standard) Integral PRV: For safety: pressure relief valve releases at 55-65 PSI

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 9.5 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 9.5 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing.  6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.

Read more less