Stainless Steel Fittings
Weldless Bulkhead 1/2'' Compression x 1/2'' MPT, Stainless Steel
Stainless steel weldless bulkhead. 1/2" compression x 1/2" MPT (male pipe thread)
$18.95
Union, 3/8''mfl x 1/2''mpt - Stainless
Stainless Steel Flare Fitting Flare to Pipe Adapter 3/8" MFL (male flare thread) x 1/2" MPT (male pipe thread)
$13.99
Stainless Steel Washer
Stainless steel washer for 1/2" mpt. 29/32" Inner Diameter 1 33/64" Outer Diameter 7/64" Thickness
$2.49
Stainless Nipple - 3/4 in x 1 in (Close)
3/4" x Close Stainless Steel Nipple
$5.95
Stainless - 1/8 in FPT x 1/4 in Barb
Stainless 1/8 inch female pipe thread with 1/4 inch barb.
$6.30
Ss Infussion Mash Tun ReCirculation T Barb
SS Brewtech's 1/2" Re-circulation Tee Barb 304 stainless steel 1/2" hose barb 1/2" fpt on mashtun side 1/2" mpt on outer side Hose clamp and silicone tubing not included.
$15.95
Quick Connector 1/2'' 90 degree Barb x 1/2'' FPT
1/2" barb with a 90 degree bend x 1/2" FPT (female pipe thread) quick connector. Metal parts are stainless steel.
$11.99 $7.99
Pickup Tube - Side
Spike Brewing's special 5/8" pickup tube flows up to 4x better than their competitors 1/2" size. These 5/8" tubes work perfectly with their full port valves which have a 5/8" flow diameter; no flow restriction. Spike Brewing's proprietary fittings uses quick connect technology. The quick connect fitting simply hand screws into the kettle and the pickup tube easily pushes in/pulls out; no tools needed. Recommend Uses: Boil Kettle - Create a whirlpool inside your kettle so hop material collects in the center of the lower stepped section. The side pickup will drain clear wort from the side, above the stepped bottom, avoiding the hop and trub material which has settled. Custom Kettles - Works as a top re-circulation arm or a whirlpool arm. Features: One size fits all kettles Large 5/8" diameter 304 stainless tube Simply push in for seal; no tools required Proprietary stainless push to connect fitting included Rests on top step for clear wort draining Made in the USA
$33.00
Male Stainless Steel Quick Disconnect w/ MPT
Male Stainless Steel Quick Disconnect with Male Pipe Thread When used with the female quick disconnect these quick disconnect seal up very well in either flow direction, without a lot of work in connecting them. It feature a 1/2" Male National Pipe Thread on the ends for easy connectivity to almost anything.The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60 psi or less. Please Note: This product will NOT work with Brass or Plastic Quick Disconnects.
$9.99
Male Stainless Steel Disconnect w/ 1/2'' FPT
Male Stainless Steel Disconnect with 1/2'' Female Pipe Thread. When used in conjunction with the female quick disconnect these quick disconnects seal up completely regardless of the liquids direction of flow, while remaining simple and easy to use. It feature a 1/2" Female National Pipe Thread on the end for easy connectivity to almost anything. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off. Note: This product will NOT work with Brass or Plastic Quick Disconnects.
$11.99
Bulkhead Washer
This is a replacement stainless steel washer for Weldless Bulkhead Assemblies.1.5" OD x 1.0" ID x 0.1" Thick
$1.00
Blow Off Cane for 7 Gallon Chronical
Works with lids with 3" Tri-Clamp fitting. Blow off cane for SS Brewtech's 7 gallon Chronical Fermenter 304 stainless steel pressure relief valve included Does not include 3" Tri-Clamp gasket
$53.95
Ss Infussion Mash Tun Hose Barb - 3/8 in. to Knurled 1/2 in. FPT
3/8" Hose Barb with 1/2" fpt Knurl for SS Brewtech Mashtun 304 stainless steel Fits into SS Brewtech's mash tun bulkhead fitting Needed for MT recirculation manifold
$11.95
1/2'' MPT x 1/2'' Male Flare Thread, S/S
1/2" mpt x 1/2" mft, stainless steel
$5.99
1/2'' FPT x 1/2'' MFT, Stainless Steel
1/2" fpt x 1/2" mft, stainless steel
$5.99
3/8" Stainless Half Coupler
Stainless steel 3/8" female pipe thread (FPT) half coupler. Note: Half couplers have thread for insertion from one side only.
$4.99
Pickup Tube - Center
Spike Brewing's special 5/8" pickup tube flows up to 4x better than their competitors 1/2" size. These 5/8" tubes work perfectly with their full port valves which have a 5/8" flow diameter; no flow restriction. Spike Brewing's proprietary fittings uses quick connect technology. The quick connect fitting simply hand screws into the kettle and the pickup tube easily pushes in/pulls out; no tools needed. Features: One size fits all kettles Large 5/8" diameter 304 stainless tube Simply push in for seal; no tools required Proprietary stainless push to connect fitting included Sized to pick up from the bottom edge of the kettle Made in the USA
$33.00 - $45.00
Quick Connector 1/4'' MFL x 1/2'' FPT
1/4" MFL (male flare) to 1/2" FPT (female pipe thread) quick connector. Metal parts are stainless steel.
$8.99
