Spike Brewing Flex Accessories
Gas Post x 1/4" NPT
Since most brewers who keg use ball lock connections for hooking up their CO2 tank we figured why not design a ball lock fitting to easily add CO2 to your conical! The Spike Brewing gas post assembly has a standard ball lock gas post on one end with a 1/4" NPT on the other. This allows it to screw directly into Spike Brewing carb stone as well as the their gas manifold. Specifications: Stainless steel Ball lock x 1/4" NPT Comes with replacement o-ring
$11.00
15 psi Pressure Relief Valve
When pressurizing your Spike Conical you'll always want to use a pressure relief valve (PRV). This will prevent the tank from being over pressurized and causing a potential failure to occur. This Spike Brewing PRV was developed with their OEM specifically to work with their CF series Conical. It will keep your tank below the 15psi max working pressure rating. The PRV also has a handy bleeder pull ring to release built up pressure. Specifications: 15 psi release 1/4" npt threads Spike Brewing's specially designed gas manifold is also now available.
$25.00
ForgeFit® Stainless Tri-Clamp End Cap Reducer - 4 in. x 1.5 in.
Connect a 4" TC fitting to a 1.5" TC fitting with this reducer. Made from 304 stainless steel.
$37.99
Carb Stone
If you didn't already know the Spike Conical is a unitank! This means it is designed to handle pressures up to 15psi. This capability allows you to add 15psi of pressure needed to carbonate your beer before transferring to your keg. This will reduce carbonation times from upwards of a week down to less than 24hrs. Spike Brewing's carb stone is designed to attach to the outside of the racking port butterfly valve. This means the carb stone can be installed when you need it and won't be sitting inside the tank during the entire fermentation process. This eliminates the chance for the stone to become clogged. It also has a protective stainless housing which prevents damaging the very brittle 'stone'. Detailed product guide:Product Guide.pdf Forced carbonation pressure chart:Carbonation Chart Carb Stone Only Carb Stone 1.5" TC Clamp 1.5" TC Gasket Gas Post Carb Stone Bundle Carb Stone Package (see above) Pressure Gauge (Link) PRV (Link) 2nd Gas Post (Link) Gas Manifold (Link) **Always use a 15psi pressure relief valve when pressurizing a tank**
$85.00 - $160.00
TC Sample Valve Gasket Set
FDA approved EPDM gaskets for all your sample needs. Go get yourself a new gasket and seal that baby right up!
$2.50
Oxygenation Kit
An oxygenation kit specifically designed for homebrewing. Oxygenate your wort easily and conveniently with a precise amount of oxygen rather than leaving it to chance. The Spike Oxygenation (O2) Kit was designed to provide homebrewers with a simple solution for oxygenating their wort prior to fermentation; Happy yeast = happy beer! The days of slow or failed fermentations are over, and a giant 10lb oxygen tank is no longer the only solution! The O2 kit is designed to attach to a standard hardware store oxygen tank and will precisely oxygenate your wort to make sure fermentation goes smoothly! With that precise flow control, eacg oxygen bottle will oxygenate up to 200 gallons of wort; saving you time and money!
$85.00
Pickup Tube Replacement O-Rings
Set of 3 replacement o-rings for the Spike Brewing 5/8" quick connect pickup tube fittings. Specifications: FDA approved Buna-N Sold in set of 3
$2.50
Leveling Feet
Want some additional leveling adjustment for your FLEX? Well the Spike Brewing non-marking leveling feet will do the trick! They also use a 304SS stud because nobody likes rust! Specifications: Non marking plastic bottom 304SS stud 3 pack
$16.00
HERMs Coil Replacement O-Rings
Set of 3 replacement o-rings for the Spike Brewing 1/2" quick connect HERMs coil fittings. Specifications: FDA approved Buna-N Sold in set of 3
$3.00
FLEX Extended Bracing Shelf
The Spike Brewing custom Spike extended bracing shelf is a recommended addition when casters or leg extensions are installed. The extended bracing shelf widens the stance of the FLEX making it more stable. This helps when going vertical with the leg extensions or mobile with casters. Specifications: 304SS Super thick 14ga material Made in the USA Bracing shelf install and instructions:Install + instructions
$55.00
Adjustable Thermometer
This Spike Brewing adjustable face dial thermometer can be orientated 360 degrees so reading the thermometer is easier. This 1/2” NPT Brew Thermometer is ready to screw directly into the kettle. This 2.5” stemmed thermometer can cover 40-220 degree ranges. The 3” glass dial will display all the information you need at a glance and while withstanding the high heat from the burner below. The thermometer also has calibration screw for added accuracy.
$40.00
Pressure Gauge
This pressure gauge can be used while pressure fermenting, briting or pressure transferring. Specifications: 0-30psi 2" Dial 1/4"npt **This accessory is to only be used with the FLEX+ or the upgraded high pressure lid**
$15.00
FLEX Leg Extension Set
Leg extensions are a great option to get th FLEX off the ground. This reduces bending over to take gravity readings, add hops, transfer, etc. The shorty leg extensions are 9” long and the long leg extensions are 18". Both screw directly into the bottom of the FLEX legs. Both sets of leg extensions can be used with the stock leg caps, leveling feet and casters. *It is recommend to use the extended bracing shelf when using the leg extensions for added stability* Shortly leg extension specifications: 304SS 9" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters Long leg extension specifications: 304SS 18" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters
$42.00 - $55.00