Best Selling Products

An oxygenation kit specifically designed for homebrewing. Oxygenate your wort easily and conveniently with a precise amount of oxygen rather than leaving it to chance.  The Spike Oxygenation (O2) Kit was designed to provide homebrewers with a simple solution for oxygenating their wort prior to fermentation; Happy yeast = happy beer! The days of slow or failed fermentations are over, and a giant 10lb oxygen tank is no longer the only solution! The O2 kit is designed to attach to a standard hardware store oxygen tank and will precisely oxygenate your wort to make sure fermentation goes smoothly! With that precise flow control, eacg oxygen bottle will oxygenate up to 200 gallons of wort; saving you time and money!

Read more less

Stainless steel elbow tailpiece with 5/16" OD Barb

Read more less

Replacement black cap plug for CMB ball lock disconnects.

Read more less

Replacement gray cap plug for CMB ball lock disconnects.

Read more less

This replacement knob is for Kegland branded CO2 tanks.  It is compatible with 2.5 - 20 pound tank sizes.      

Read more less

Made from high quality 304 Stainless Steel, this condenser lid is ideal for apartment or basement brewers who struggle managing steam and condensation during brewday. Easy to use and assemble, can be used with a wide range of configurations. Comes with removable end cap for adding hops, yeast nutrient or whirlfloc during the boil. (Use gloves, it will be hot!). This steam condenser set can be compatible with the 35L or 65L BrewZilla/DigiBoil with the stainless distillation lid and 2 Inch Bulkhead. This unit can allow brewing indoors without that pesky sticky steam gumming up your freshly painted interior! The End Cap can be removed for brewing salts/hops and other brewing essentials to be added during the boil. Please note hot steam through this port can lead to serious scalding, please use heatproof gloves. Not only will you get to the boil faster, but you will use less power overall to maintain a rolling boil as there will be less area for the heat to escape. No need to install inside a kitchen, or in the garage with a special range hood. Simply attach this to the Condenser Lid and run your kitchen tap or garden hose to the Duotight-compatible inlet. You don't not need super-fast flow rate to cool boiling steam into liquid. Different to distillation where you require the distillate to be under a certain temperature so that ethanol doesn't evaporate from the liquid at a high rate, with boiling wort you just need enough to form a liquid! Pretty simple. Eco-Friendly option if you have the means to save/collect the coolant water. Can be re-used on the garden or for cleaning later on. Please note the water discharging will be very hot! The Spray head can condense 0.42 gal (1.6 L) per minute while connected to 100 psi mains water. Caution: You will need to remove the Steam Condenser when you reach boil to manage the hot break and ensure you don't have a boil over when you reach boiling temperatures. Once you've completed that step, you can reattach the Condenser and leave it in place for the remainder of the boil. You Will Also Need: Distillation Lid for 35L or 65L BrewZilla / DigiBoil (Pro Sight Glass Distillation Lids coming soon) 2" T.C. Weldless Bulkhead 6.35 mm Monotight Adapter (or you can clamp directly to the inlet) Kit Includes: 5 x 2" Tri-Clamps 5 x 2" Tri-Clamp Silicone Seals 1 x 13.7" (340 mm) Long 2" T.C. Tee  1 x 7.8" (200 mm) Wide 2" T.C. Tee 1 x 2" T.C. End Cap 1 x 2" T.C. to 6.35 mm Monotight elbow cap with elongated spray head mister 1 x 2" T.C. x 0.47" (12 mm) Barb – Suitable for 3/8" (10 mm) ID Silicone tubing Some of these fittings are not sold separately

Read more less

304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 18" long.

Read more less

The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. This particular sized tri-clamp Hop Bong was designed for the BrewBuilt X-Series Uni Conical fermenters for their 1.5" T.C. lid port. The side port features PCO1881 male threads so you have the option to add a Ball Lock Cap. When used as a dry hopping device on top of your fermenter, this will allow you to purge your additions of oxygen by flushing them with CO2. When used as a sight glass below your fermenter (if your conical has a 1.5" bottom port, or if you use it along with a 2" x 1.5" reducer), bubble CO2 from the bottom up via the Ball Lock Cap to rouse hops or carbonate finished beer. Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic. Hop Pellet Capacity: 80–120g (2.8–4.2 oz)

Read more less

Weyermann® Barke® Munich Malt brings forth enhanced body and dark-beer aroma, and richly malt-aromatic with notes of honey, and biscuit.  Barke® Munich malt, like the other Barke® Line malts possess excellent process characteristics in the brew house and during filtration, along with increased extract efficiency, strong malt flavor and classic characteristics for original Munich Dunkels.Suitable for Dark Beers, “Schwarzbier”, “Festbier”, Bock Beer, Octoberfest styles, Belgian Dubbels, “Kellerbier”, Stouts, and Munich Dunkels. Specifications: Color °L : 6.9 - 8.7 Moisture % Max : 4% Extract FG Min : 78 Protein Total : 9.5 - 11.5 Usage Rate : Up to 100% 55 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less

Weyermann® Barke® Vienna Malt creates full-bodied beer, with golden color, smooth taste, and intensely malty-sweet flavors. Gentle notes of honey and nuts (almond and hazelnut) also come through when using this malt. Excellent process characteristics in the brew house and during filtration, along with increased extract efficiency set Barke® Vienna Malt apart. Weyermann® Barke® Vienna Malt is the malt for authentic lagers. Perfect for Bavarian Dunkel, "Festbier", "Maerzenbier", Pale Ale / IPA, Lager, Stouts and of course Vienna Lager. Specifications: Color °L : 2.7 - 3.8 Moisture % Max : 5.5% Extract FG Min : 79 Protein Total : 9.5 - 11.5 Usage Rate : Up to 100% 55 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less

This polypropylene base board comes with pre-drilled hole locations for mounting the MaltZilla motorized grain mill. Board Dimensions - 17.75" x 13.5" x 3/8"

Read more less

2.5 pound aluminum CO2 cylinder. Ships empty. Will dispense approximately 4-5 five gallon kegs before needing to be refilled.  

Read more less

The Hungarian oak at Medium toast displayed a high perceived-vanillin content, with roasted coffee, bittersweet chocolate and black pepper characters. Hungarian oak provides unique attributes such as leather and black pepper that is not noticed in other oak varieties. Cubes (also known as Oak Beans) offer the home winemaker control and flexibility during red and white fermentations and aging. StaVin’s slow fire-toasting creates the same traditional flavors found in the production of fire-toasted barrels. Unlike Fermentation Chips, Cubes offer a slower, more complex extraction, matching barrel flavors. Best results will be achieved by fermenting with the Cubes and leaving them in the wine for the duration (until filtering and bottling). Using Oak Cubes aids in the stabilization of color and helps cross-link tannins, which builds structure in wine. For 100% New barrel impact:  Use 1.5 lb (680 g) per 60 gal (227 l) 8 ounce package.

Read more less

3" x 2" tri-clamp concentric reducer. Made from 304 stainless steel.

Read more less

304-Polished Stainless tee with 2" tri-clamp connections.

Read more less

French oak provides a fruity, cinnamon/allspice character, along with custard, milk chocolate, and campfire/roasted coffee notes.  The campfire/roasted coffee notes are more noticeable with higher toast levels.  As the toast levels increase, the fruity notes for the wine changes from fresh to jammy to cooked fruit/raisin in character. Cubes (also known as Oak Beans) offer the home winemaker control and flexibility during red and white fermentations and aging. StaVin’s slow fire-toasting creates the same traditional flavors found in the production of fire-toasted barrels. Unlike Fermentation Chips, Cubes offer a slower, more complex extraction, matching barrel flavors. Best results will be achieved by fermenting with the Cubes and leaving them in the wine for the duration (until filtering and bottling). Using Oak Cubes aids in the stabilization of color and helps cross-link tannins, which builds structure in wine. For 100% New barrel impact:  Use 1.5 lb (680 g) per 60 gal (227 l) 8 ounce package.

Read more less

Kegerator tower coolers help eliminate initial use warm beer and foaming by blowing cool air from the refrigerator into the tower. This keeps your beer shanks and faucets cold.   Includes: Blower and fan motor 3/4" I.D. tubing AC power supply Cable tie

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 9.5 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 9.5 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing.  6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.

Read more less

Variable Capacity tanks, also called Variable Volume tanks, made in Italy by Marchisio. This style of tank features a ‘floating’ lid with an inflatable gasket that can be positioned at any height in the tank. Use the included air pump to inflate the lid gasket. Whether you position the lid directly on the liquid, just above, or at the top of the tank is up to you. They are used as affordable stainless production tanks for applications ranging from winemaking to pickled foods and Kombucha.  Includes: 304 Stainless Tank 304 Stainless Floating Lid Food-Grade Floating Gasket Air Pump with pressure gauge Connection kit for connecting gasket to pump Dry Airlock for tank Chrome Plated Spigot 100L Specifications: Nominal volume: 100 Liters (26.4 gallons) Effective volume: 93 Liters (24.6 gallons) Diameter: 50 cm (20 inches) Height: 60 cm (24 inches) Valve size: 1/2" BSP Thickness (Bottom X side, in mm): 1.0 X 0.7 *Please Note: Tank may differ slightly from image shown. Stands are sold separately. Due to size of this item, it is available for pick-up only.

Read more less

EnoItalia Stainless Stand and Chute This stand was specially designed for the Enoltalia Crusher/Destemmer.  It is just tall enough to allow grapes to drop directly into your fermenter or transfer container. A regular garbage can can be placed at the end of the unit to collect stems. By using the stand you eliminate the need to move the must and stems from container-to-container, thus saving time and energy. This model fits our EnoItalia Crusher/Destemmers. It does not fit models from other manufacturers.Please Note: This stand comes broken down, and will require assembly. Estimated Overall dimensions: Footprint: 32 1/4" long x 22" wide Height: 32" high. Top Tray Inside dimensions 32" long x 14" wide

Read more less

Replacement check valve for Micro Matic party pumps.  For Micro Matic HP-100, 300, 500, 700 & 900 series pumps.

Read more less

Replacement piston rod 0-ring for the Micro Matic 4" and 8" chrome pumps. Dimensions: O.D. 1-7/16" I.D. 1-3/16" x W. 1/8"

Read more less

The Filter Pro is a vertical (gravity-fed) filter and is the latest release from Still Spirits. Processing up to 2.1 gallons (8 L) of spirit at a time. Easy-to-use tri-clamps, flow control, and a removable door and wall mount.Perfect for home distillers who want to upgrade their existing filtering system or new distillers who want to create the cleanest of spirits from the get-go, the Filter Pro offers a user-friendly solution and superior results! KEY FEATURES Made from 304-grade stainless steel. Filters an impressive 2.1 gallons (8L) of spirit at a time. Fits up to 500g of loose Still Spirits Activated Finishing Carbon to remove unwanted flavors from distilled spirit. Additional filter papers included to prevent dust and carbon particles. Long stainless-steel shaft ensures maximum contact time with the carbon. Filter where you want with the removable door & wall mount. Easy to connect tri-clamps & adjustable flow control. The quality stainless-steel build means the Filter Pro looks sleek and impressive in any space your customer decides to mount it - made possible with the removable door and wall mounts included. Even the box it comes in is designed to jump off the shelf. INCLUDED IN THE BOX: Hopper Hopper Lid Wall-mounted bracket Door-mounted bracket Mounting fasteners x 2 Filter Column Ball Valve Tri-clamp clamps x 2 Tri-clamp seals x 2 Filter papers pack of 5 500g SS Loose Carbon x 1

Read more less

Carbon filterting neutral spirits is done to remove the fusel oils that give spirits a harsh taste and smell. This kit has been designed to be used with small amounts of neutral spirit up to 1L at a time. Kit Includes: 1 - 2" T.C. Extension Tube 2 - 2" Tri-Clamps 1 - 2" Silicone Gasket 1 - 2" Teflon Gasket w/ Mesh Screen 2 - 2" T.C. x 3/4" Female BSP 2 - 3/4" x 1/2" BSP Reducing Bush 2 - 9.5 mm Duotight x 1/2" Ball Valve 1 - Roll of Plumber's Tape 1 - 500g Pouch of Food Grade Activated Carbon  

Read more less

Produced by smoking pale malt over burning peat. Peated Malt will add a dark, earthy, phenolic aroma and flavor characteristic of Islay whisky. It is also suitable for smoked beer styles, a little goes a long way! Specifications: Color Range °L : 1.3 - 1.7 (2-3 EBC) Target Color °L : 2.5 Moisture % : 5 Origin : United Kingdom Maltster : Simpsons 55 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.  

Read more less

Standard stainless steel spout replacement for Intertap and Nukatap faucets.

Read more less

Unmalted flaked barley. Use at 10-25% of total grist to produce a light colored, mild flavored, dry beer. 50 pound bags of grain are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less

Weyermann® Dark Wheat is a gently kilned malt made from high-quality German wheat. It contributes a mild golden color to wort and a robust malty-sweet flavor with notes of bread, biscuit, honey, toffee, and caramel. Wheat malts are high in protein, which helps produce fuller-bodied beers. Wheat malt can also improve head formation and retention, depending upon the other grist constituents. In top-fermented beers, Weyermann® Dark Wheat malt performs especially well, adding creaminess, body, and complex wheat flavors. Weyermann® Dark Wheat malt has a somewhat 'drier', more complex character than pale wheat malts. It's the signature malt for Bavarian Dunkelweizen, and perfect for Weizenbocks, Kölsch, and Altbiers. Specifications: Malt Type:  Specialty Grain Origin:  Germany Color:  6.2-8.1 °Lovibond (15-20 EBC) Protein: 10.5-14% Moisture:  5% max. Extract (dry):  81% min. Usage:  50% max. 55 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less

Rahr Red Wheat is a pale wheat malt made from North American hard spring red wheat. Pale wheat malt has the sweet malty flavor of other malted grains, but with a hint of fruitiness. Wheat malts are high in protein, which helps produce fuller-bodied beers. Wheat malt can improve head formation and retention, depending upon the other grist constituents. Red wheat has a slight tartness to its flavor not present in white wheat. It also has smaller, harder kernels than white wheat, which can require careful milling. Rahr Red Wheat is suitable for all wheat-style beers. Product Specifications: Color °L : 2.4-3.5 Moisture % Max : 5.0 Protein Total : 12.0 +/- 3.5 Extract FG Min : >80.0 Usage Rate : Up to 50% 55 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.  

Read more less

Briess 2-Row Caramel 120L is a very dark crystal malt made with 2-row barley. It imparts deep red color and pronounced flavors of burnt-sugar, raisin, and prunes. Crystal malts also add body and improve head retention. Usage is progressive, starting light to add deep richness to pilsners and reaching the maxiumum 15% to impart color and raisiny flavor to darker ales, stouts, and porters. Crystal malts are gently cooked during the malting process. Cooking initiates the enzymatic conversion of starches into fermentable sugars, and caramelizes some of the sugars as the malt reaches its final color. This eliminates the need to mash crystal malt, and ensures that some of the sugars will survive fermentation to sweeten the beer. Briess caramel malts are roaster produced to create glassy, crystallized sugars with rich flavor and color. Specifications: Color °L : 120 Moisture % Max : 3 Extract FG Dry : 75 Usage Rate : Up to 15% 50 pound bags are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less

Caramel Steam malt is created via an innovative process that develops crystal characteristics and a rich, nutty flavor. Caramel Steam can be used as a direct substitution to crystal malts for those desiring crystal-like flavors, but wanting a softer sensory impact. Specifications: Color °L : 35 - 45 Moisture % : 5 Protein Total % : 12 Max Usage Rate % : 20 55 pound bags of grain are excluded from flat rate / free shipping offers. Also available by the pound.

Read more less