Regulators & Repair
1/4'' NPT Plug
1/4" NPT plug, left hand threads, Allen socket head, for primary regulators
$1.75
1.6'' Diaphragm Regulator Repair Kit
This kit contains everything you need to service your 3700 series TapRite regulator after years of use. It includes a 1.6" diaphragm, capsule, and tank nipple o-ring which are the most common wear and leak points.
$19.99
Inlet Co2 Filter
The inlet Co2 filter helps to filter out contaminates from Co2 Gas. Inserts inside the Micro Matic Premium Regulator inlet stem.
$2.00
Beer Nut Inlet Seal
Beer Nut Inlet Seal for Micro Matic Premium 640 Series Regulators.
$2.00
CO2 Regulator Inlet Stem
Replace CO2 Inlet Stem for Micro Matic Premium Series CO2 Gas Regulators. Specifications: Right Hand 1/4" NPT Chrome Finish 2-1/4" Length Does not include Inlet Seal, Inlet Co2 Filter, or Nylon Inlet Seal.
$18.00
Nitrogen Regulator Inlet Nipple - LHT
Replacement inlet nipple for nitrogen regulator with 1/4 left hand thread.
$9.99
Nitrogen Regulator Inlet Nipple Nut
Replacement inlet nipple nut for nitrogen regulator with CGA-580 thread.
$10.99
Bonnet Spring 0-60
Replacement bonnet spring for beer keg regulators 0-60 psi.
$6.99
KOMOS Regulator Diaphragm and Seat Assembly
Over time the internal diaphragm can wear out and result in drifting pressure or a slow leak through the regulator body. Replacing the diaphragm is usually the best path to the fixing these issues so your regulator can return to holding consistent pressures. Compatible with both the single and dual-body KOMOS regulators.
$8.99
Pressure Gauge, 0-15 PSI
Replacement low pressure gauge for Co2 regulator. Looking to dial in your dispensing pressure? The maximum reading on this gauge is 15psi allowing you to adjust to that perfect pressure. 0-15 PSI 1/4" NPT bottom inlet Right hand threads
$14.99
2" Connector Nipple - 1/4" NPT
Use to connect secondary regulators 1/4" NPT x 1/4" NPT Right hand thread
$4.99
Premium Plus Regulator Service Kit
Rebuild a Micro Matic Premium Plus Series Regulator with this 7-piece service kit. Includes the disassembly torque tool. Included: (1) Tamper evident cap (1) Cartridge bolt (1) Lock ring (1) Diaphragm (1) O-Ring (1) Disassembly torque tool (1) Instructions
$39.99
Kegland Replacement CO2 Tank Knob
This replacement knob is for Kegland branded CO2 tanks. It is compatible with 2.5 - 20 pound tank sizes.
$4.99
2.5lb Co2 Aluminum Cylinder - Empty
2.5 pound aluminum CO2 cylinder. Ships empty. Will dispense approximately 4-5 five gallon kegs before needing to be refilled.
$65.99
Duotight 8mm Inline Plastic Regulator
These regulators work great for reducing your main pressure from 0-150 psi. Suitable for both gas and liquid. The 8 mm Duotight inlet and outlet are compatible with EVABarrier tubing. Specifications: Pressure Range: 0–150 psi Suitable for mains water pressure Liquid and gas compatible Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Wall mountable Made from non-corrosive acetyl, nitrile, and stainless parts
$9.49
3-Way Gas Manifold
3-way horizontal gas manifold without safety pressure release. 3/8" barbed inlet (3) 5/16" barbed shut-offs Shut-offs do not include check valves Aluminum body
$44.99
Regulator Bonnet Gasket
Replacement bonnet gasket for regulator. 2" outer diameter.
$3.50
Mini CO2 Regulator
Portable, mini, two stage co2 regulator with a range of 7-21 PSI. This regulator uses 74g cartridges and provides constant pressure to your vessel. Cartridges not included.
$69.99 $59.99
Duotight BlowTie Diaphragm Spunding Valve
The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a keg while doing pressure transfers. Thanks to the large surface area of the diaphragm, this style spunding valve is much more accurate than the poppet style. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing. The blow off pressure can be set by either pairing the BlowTie with the Push-In Pressure Gauge, or by attaching it to an empty keg that has been pressurized to the desired psi. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends 0-40 psi pressure rating
$14.99
2'' Flat Seal, Regulator Repair Kit
Regulator repair kit for 2" diaphragm Taprite co2 regulators (series 740, series 1660, series 5260, series 5740). Includes diaphragm, capsule, and flat tank seal.
$19.99
10lb Co2 Aluminum Cylinder - Empty
10 pound aluminum CO2 cylinder. Ships empty. Will dispense approximately 18 five gallon kegs before needing to be refilled or exchanged. Dimensions: 20.75" Tall x 7" wide.
$124.99
Connector Nipple, 2" x 1/4" NPT
This brass nipple is 2" in length and has 1/4" NPT, right hand threads (rht). It is commonly used for connecting regulators and air distributors/manifolds.
$4.99
Pressure Gauge
This pressure gauge can be used while pressure fermenting, briting or pressure transferring. Specifications: 0-30psi 2" Dial 1/4"npt **This accessory is to only be used with the FLEX+ or the upgraded high pressure lid**
$15.00
6-Way Modular Gas Manifold
This modular gas manifold will allow you split one CO2 line to six of them. Each line can be turned off individually without affecting the flow to other kegs. Each ball valve contains a check valve that ensures no beer or gas can flow between the two kegs. The barbs are all 5/16" which is standard for gas line in the beer industry. If later, you decide to add an additional keg this manifold can be expanded using the Add On Assembly.
$69.99
